UNI-Flash & Live CD/USB STEA Edition v.03.2012 (13.06.2012)



UNI-Flash & Live CD/USB STEA Edition v.03.2012 (13.06.2012) | 4.66 GB

Basis Live CD / USB STEA Edition - STEA LiveXP - Originalnye build WinPE (SteaPE) based on Winbuilder Nikzzzz c network support and multimedia.
A. Live CD / USB STEA Edition
The main distinctive features in comparison to similar products:
- The ability to download version of the WIM-file work properly on the PC, available RAM from 128 MB, thanks to an integral part of the system and phased WIM-load modules;
- Availability of the automatic adaptation of the operating system to a different amount of RAM PC;
- Location of all major components of the Live CD / USB (except the startup files) in the same directory that greatly simplifies the use of an assembly consisting of a multi-system or as an emergency resuscitation system on your hard drive the PC in addition to the core OS;

More
Applied kompanovki scheme enables easy integration of Live CD / USB STEA Edition in full in any multiboot projects built on the basis of downloaders GRUB4DOS or SYSLINUX / ISOLINUX. You do not need any renaming and re-launch of ways.
All components of the Live CD / USB in the directory STEA, and assembly for use in the multi system enough to move to the media one single folder, and addressed to the startup menu file STEA.LST, which is also located in the directory STEA.

The lines in the menu to go to the multiproject build the menu:

A. For GRUB4DOS (G4D)
Code:
title Live CD / USB STEA Edition
configfile / STEA / STEA.LST

Two. For SYSLINUX / ISOLINUX
Code:
LABEL STEA
MENU LABEL --- Live CD / USB STEA Edition
BOOT / STEA / BOOT / STLDR

If you use a software package LiveXP CD / USB STEA Edition in full-on Windows, for quick mounting and opening a stand-alone menu except the folders AdminSuite STEA should be placed in the root directory batch file STEA_Live.bat.

- Availability of a simple scheme user customization, which allows to install and maintain! SteaPE system parameters and some basic configuration interface

The scheme of user settings SteaPE as follows:
A. In the directory \ STEA \ SETTINGS \ MARKERS are cookies *. Ini with the names of those included tuning parameters.
To enable a specific tweak is required only to move (or copy) an appropriate marker file in the folder \ STEA \ SETTINGS \ MARKERS in the directory \ STEA \ SETTINGS.
When using SteaPE with accommodation set in Flash, of course, is just a basic and very rapid.
When used in the embodiment SteaPE CD for setup is enough to open the image in the assembly UltraISO, move the appropriate markers in the directory \ STEA \ SETTINGS, save and burn to a disc image file to a new CD.

Two. Custom MARKERS
AUTOMAX.INI >>> autostart setting the maximum resolution the screen after loading the video driver
BUTTONBAR.INI >>> Autorun utility ButtonBar
CLASSICMENU_SMALL_ICONS.INI >>> classic "Start" menu with small icons
CLASSICMENU_STD_ICONS.INI >>> classic "Start" menu with the standard icons
COMM_DRV.INI >>> use "common" drayverpak \ PeDrivers, hosted at the root of the carrier
DISPLAY_1024_768.INI >>> 1024x768 screen resolution at boot
DISPLAY_1280_720.INI >>> 1280x720 screen resolution at boot
DISPLAY_1280_1024.INI >>> 1280x1024 screen resolution at boot
DISPLAY_AUTO.INI >>> automatic installation of the screen resolution at boot
EXP_STD_ICONS.INI >>> The standard size of the icons on the toolbar of the conductor
EXP_VIEW_ICONS.INI >>> Windows Explorer type of "Icons"
EXP_VIEW_LIST.INI >>> Windows Explorer view "List"
EXSYSTEM_REGDLL.INI >>> libraries enable autoenrollment. DLL,. OCX, add the user to the directory \ STEA \ SYSTEM (% EXSYS%)
HWPNP_NOAUTO.INI >>> disable autorun at startup utility installation HWPnP
NO_RAM.INI >>> disable the script automatically load into the RAM of the entire system - the second part of the system is installed on only a RAMDisk, staying on the boot media in order to save resources, RAM
PAGEFILE_NO_AUTO.INI >>> disable the auto-page file on startup
PUNTOSWITCHER_AUTO.INI >>> Autorun utility PUNTOSWITCHER
ScrollMouse_AUTO.INI >>> Autorun utility ScrollMouse loading (the mouse wheel skrolirovanie window under the cursor)
THEME_NOSAUND.INI >>> disable the auto sound system circuit PeSaund alerts at system startup
WB_THEME_NOAUTO.INI >>> disable the auto WB Vista theme during startup
WINTEMP.INI >>> script to include the destination directory \ Windows \ Temp standard (desktop) system as an address directory% TEMP% and% TMP% SteaPE
ZPNP_NOAUTO.INI >>> disable Autorun utility to install drivers (ZPNP) after the system boots

- To increase the mobility of STEA Live in a full-featured system adds support for 3G modems HUAWEI for all the major GSM operators in Russia;

3G Connect
Manager 3G modem HUAWEI.
Embedded profiles BeeLine, Megafon, MTS, Tele2, Smarts. Maybe add profiles of regional operators. Full support for all functions of a modem, including voice and SMS.

In the folder \ Programs \ Internet \ 3G_Connect have little instruction in the use of Stea Live and useful tools for adaptation HUAWEI 3G Modem to all GSM operators RF and more ...




The interface and the shell SteaPE standard, without compromising permissions and parameters of graphic elements.

HELP / Install CD version of Live XP Build a Flash Drive
Installing a Flash includes three stages:
A. Bringing Flash to the format of the disk "bootable HDD".
Two. Moving to Flash files in the assembly
Three. "Binding" boot to the startup file assembly \ STEA \ STLDR (or \ STEA \ STEA.LST)

If your Flash-ROM is bootable, skip the next three paragraphs ...

Before you begin to format Flash, I recommend to try to perform
installation, relatively speaking, in "one click".
For a considerable number of "running" and "youngish" Flash, with the FAT file system, or
FAT32 the whole setup can be realized by a script SETUP_TO_FLASH, available at
part of the assembly itself. Moreover, Flash drive is not required to be empty -
only necessary to have sufficient free space, and existing files and
directories during the installation of STEA Live not be affected. Run the script
possible and from the assembly (the label is on the desktop), and just to drive in standard or Widows
even with the ISO image that is connected via a virtual drive - the script file \ STEA \ TOOL'S
\ SETUP_TO_FLASH.BAT
The sequence of actions:
Connect Flash to a USB> Flash to create the root of an empty directory \ SetupSTEA> run
the script.

If the script is not received SETUP_TO_FLASH boot disk or Flash
disc has the original file system NTFS, you must first prepare the Flash and
make a "bootable HDD". Perform the necessary operations can be utility BootICE,
available in the assembly \ STEA \ PROGRAMS \ HDD-Utilites \ BootICE.
You can do everything from Live, and of the standard WINDOWS \ STEA \ PROGRAMS \ HDD-Utilites \ BootICE
\ BootICE.exe
The sequence of actions:
1.Formatiruem Flash
PartsManage> Reformat> USB-HDD> 63> FAT32> OK
Two. Prescribes the boot sector of a disk in the MBR
Process MBR> UltraISO USB-HDD +> Install

After that, I recommend re-try the installation using the script
SETUP_TO_FLASH. If you fail again, it is likely that the controller of your Flash
disk requires more complex manipulation (using special tools) for
bring to a format of "boot HDD".

If your Flash drive is bootable, then the "training" is required and sufficient
only:
A. Move by simply copying the directory on the Flash Disk \ STEA and root assembly files
AUTORUN.INF and STEA_LIVE.CMD (files have a helper function, and their placement in
the root of Flash drive is desirable but not mandatory. They simply more convenient to start the programming menu of the disc when using the standard Windows.)
Two. Run "bind" to an existing Flash-boot menu:

options for the boot loader GRUB:

Code:
title Live CD / USB STEA Edition
configfile / STEA / STEA.LST

title Live CD / USB STEA Edition
configfile / STEA / BOOT / STD.LST
- Option for the loader SYSLINUX:

Code:
LABEL grub
MENU LABEL Live CD / USB STEA Edition
BOOT / STEA / BOOT / STLDR


Two. UNI-FLASH-STEA 1203
UNI-Flash STEA Edition - the image of the combined system to be deployed on USB-drive (the required amount of Flash or USB-HDD disk - 3500 MB or more), includes CD-ROM version of the full-fledged Windows 7 Ultimate SP1 / USB-boot /, compiled by based on the distribution OPTIM v.3, and expanded version of Live CD / USB STEA Edition.
For both systems (UW7-STEA and STEA Live) bind to a common set of software products.

To create a system disk image utility used HDClone - very compact and high-quality tool to backup HDD.

HELP / To deploy an image UNI-FLASH-STEA
A. Place the downloaded folder in the root of HDClone Images! any part of your PC
Two. Connect the target disk - Flash or USB-HDD
Three. Run the utility \ HDClone Images \ HDClone.exe and select the recording mode of the image "RECOVERY":
- "Restore disk" to record the full Flash or Disk USB-HDD;
- "Restore partition" partition HDD for recording
To go on operations, press the "NEXT" ...



4. When you deploy an image to a partition USB-HDD after recording with the help of staff needed to manage disks (or any third-party manager, for example, attached to the hand scraps BootIce) designate the target partition active!
Five. Be sure to check the status of the activity of Flash! - Some combination of controllers Flash, BIOS and mate. fees when deploying an image section for some reason, a sign of activity is not recorded (the reason is still unclear).

Features of Windows 7 USB
A. Completed adaptation of the system to work with the USB-drive.

Two. The system is placed in a virtual drive and works out of the dynamic VHD format.
You can download and the system of differential VHD.
What does this mean?

Features of the system a virtual disk.
The system disk consists of a base (core) VHD and differential (secondary) VHD.
In the directory \ STEA with base VHD is expanding its diff STW7-diff.vhd, and in the boot menu, there are two rows of the loading diff-VHD.
With the 1203 version of the download diff-VHD is used as the initial menu bar Windows (default) - (WORK mode).
When you boot from a differential VHD all! changes to the system partition, made and stored in the current session will be made only in the diff-VHD, and the base will remain the same!
Boot from VHD ground running on the third line of Windows-menu (SAVE mode)

The system is available on a dynamic virtual disk (dynamic VHD) size 15,000 MB (initial size of the image file 1775 MB).
It can be seen in "Disk Management".
Dynamic Drive - that is, its an image file will be self-increase as filling the disk.
15 000 MB - this is already incorporated in the disk size limit. But it can be increased if desired.
Prior to that, the size of the disk can grow your own.
In the 1203 version:
The system is available in "dvuhparteynom" VHD - VHD in the two sections of the system and user - (ReData-"Replace Data"-the data being moved, "Real Data" - data in real time, no write-).
Made it possible to separate the application of EWF for the two parts of the system.

In the initial state of the system partition is limited to an increase in the size of the section marked-up - 3000 MB, the user partition - 500 MB. - See "Disk Management".
Made so as to ensure "a refinement" VHD at samorasshirenii in the amount of Flash 4 GB.
When placed on a larger carrier, respectively, can increase the size of the labeled sections - a system of up to 10,000 MB, the user - up to 5000 MB.
The sequence of actions:
A. Boot
Two. Run the command "EWF-Save-bootcommand-ENABLE"
Three. Through the "Disk Management" is appropriate to extend down to size
4. With the already overloaded system volume expanded.
You can not make the total increase in system and user partitions than the free space on the section of the carrier VHD!
Otherwise, when samouvelichenii VHD image file may be corrupt!

Three. In sostave system is activated and the EWF (Enhanced Write Filter). The controls are placed in the start menu.

EWF management team
UNI-Flash & Live CD / USB STEA Edition v.03.2012 (UPD.13.06.2012)
EWF-Status - call information on the status of EWF
EWF-Save-REBOOT - save changes to the system partition and reboot the PC
EWF-Save-PC OFF - save changes to the system partition and turn off PC
EWF-Save-bootcommand-ENABLE - save the changes to the system partition, disable EWF and form a team to include EWF on the next boot PC
EWF-Save-DISABLE - Do not use (disabled) EWF
EWF-bootcommand-ENABLE - form a team to include EWF on the next boot PC

Attention! When the EWF-saves at the end of the transfer is made "pending data" on the system volume, and off the PC runs much longer than usual! Do not rush off to force PC!
For visual control of data recording is recommended to use Flash with LED indicator to access devices.

New features in the EWF in v.1203:
Two-band scheme is applied EWF - the division of the whole field of EWF on the system and user - (ReData-"Replace Data"-the data being moved, "Real Data" - data in real time, no write-).
In user data area - profiles and user files (Users), ProgramData, catalogs and winevt prefetch, and MyProgram - directory for installing programs and utilities that are constantly writing their logs and *. Ini.
In the system - the rest of the system.
It was found convenient to polzovatelkoy of the filter off (with the possibility of inclusion and use).
With this construction and the use of EWF is removed taking care of your custom settings, and these programs - to save runs continuously full-time (normal) way.

EWF management team in pictures
(1) A set of shortcuts in the Start menu shortened - by the most useable and a shortcut to open the entire catalog of labels (2) EWF-MGR (ALL Command Link) (with tooltips for the purpose of commands)
(2, 4) The label command to save the user area of ??EWF.
(3 - 5) Also all the control buttons EWF (with tooltips for the purpose of commands) can be found in the software menu EWF-MGR
(5) The label command to disable the EWF user of the system.




4. Carried out additional system integration drayverpakov Mass Storage, chipsets, network cards, USB Devices;

Five. Made a modification of the system to activate the Physical Address Extension (PAE), which allowed the x86 (32-bit) system to see and use the RAM above 3 GB (theoretically available amount of RAM - 128 GB). Start Menu of Windows 7 has two options start - with the activation of PAE and the standard. As DEFAULT involved a standard startup mode;

6. Has a function of the use of "mobile" (equity) of the paging file hosted on a USB-carrier, which increased the autonomy and its own resources system. In the original version of the UNI-Flash pagefile founded in 512 MB (\ STEA \ SWAP \ pagefile.img).
If you prefer, you can delete it or replace it with 256, 1024 or 2048 MB - in the directory \ STEA \ SWAP meet the appropriate EXE-file;

7. The system added RAM-disk for use with temporary files;

Eight. Of the applications added to the system: 7-zip, ImDisk to implement RAM-disk, VHD-MGR to simplify working with VHD, Unlocker for the service.


Three. Bonus Application for UNI-Flash - BONUS catalog
To add them into the project directory PMAGIC simply copy or extract (replacing files on-demand system) sfx-pack W7PE.exe in the directory \ STEA.
In the 1203 version made a modification of Win7 PE - VHD:
- Bind to a common set of software products;
- Involved is common to all Windows "mobile" swap file;
- Returned to the system of nominal sheath - Explorer.
Win7 PE has a small feature - shutdown and restart the PC should be performed using appropriate labels placed on the taskbar next to the Start button.

Attention! Extras. Information for those who might be to embed the contents of the UNI-Flash to other multiproject or move yourself to other media or sections of HDD!
A. Objects and a migration path: directory \ STEA boot \ STLDR
Two. Home record for GRUB4DOS

title --- UNI-Flash STEA Edition
find - set-root - ignore-floppies - ignore-cd / STLDR
rootnoverify
chainloader - force / STLDR


HELP / UNI-Flash installation on HDD
Installation is performed from the loaded to the UNI-Flash Win7 without using the original image or other distribution, without formatting the target partition.
Installation can be performed on a non-empty partition (including on the system) - the existing files will not be affected.
Setup time from 2 to 15 minutes, depending on the characteristics of high-speed Flash and HDD.

During installation, the target partition will be assigned to active and will be changed to the boot sector! The original boot sector will be saved in the root partition to a file _bootsect_.bin
For a successful migration UNI-Flash STEA Edition on a local HDD:
A. Boot into Win7 UNI-Flash.
As a target, choose the main HDD partition with NTFS file without compression!
Under this condition, additional file operations are not required, it is only necessary that there is sufficient free space on target partition.

Two. Create the root directory of the target partition is empty STEA_Setup, close all applications that use the target partition, and windows to access it and run the utility USB2HDD.exe.

Note:
If at the time of installation of UNI-Flash on your computer already has installed OS Windows, you will be saved from the possibility of launching multimenyu:
- Windows XP (or any Win 2k) from a single point multimenyu (5th row);
- Windows 7 or Vista from their own menu, starting multimenyu assembly and common to all Win7/Vista menu (4th line in the boot menu Win7 VHD).

Work USB2HDD.exe provided and can only be loaded from the Win7 UNI-Flash, that is, Only when there is relevant data!

Addition to describing the migration of UNI-Flash on HDD
According to the results of tests of various installations UNI-Flash, conducted an-al-vel, the conclusion about the feasibility of a mobile configuration for Win7 UNI-Flash, placed on the Local HDD


Código:
http://www.netload.in/dateiNfekOSVW5b/hdclonise.part01.rar.htm
http://www.netload.in/dateipSNUrK7wBv/hdclonise.part02.rar.htm
http://www.netload.in/dateiEdTSshDAtC/hdclonise.part03.rar.htm
http://www.netload.in/dateiOXZgvQXCx7/hdclonise.part04.rar.htm
http://www.netload.in/dateibuxfElFGeL/hdclonise.part05.rar.htm
http://www.netload.in/dateiOEzvi3E8GH/hdclonise.part06.rar.htm
http://www.netload.in/dateipTobJpE6Jd/hdclonise.part07.rar.htm
http://www.netload.in/dateiqx5gNbYPEM/hdclonise.part08.rar.htm
Mirror :

Código:
http://letitbit.net/download/02086.0f6bd1574b7126ca8f8e5fd518f2/hdclonise.part01.rar.html
http://letitbit.net/download/04952.03425c6918d86e515a7ffa56bed9/hdclonise.part02.rar.html
http://letitbit.net/download/79616.788854657b51b7f4195e2298655a/hdclonise.part03.rar.html
http://letitbit.net/download/24899.21da12cb194be25d22a83f1f55d9/hdclonise.part04.rar.html
http://letitbit.net/download/64113.69936a7fe6c01f043bc2e4a88e9d/hdclonise.part05.rar.html
http://letitbit.net/download/77976.720330a68fbd3e54edb28560f5f5/hdclonise.part06.rar.html
http://letitbit.net/download/08725.09239fc6ac8d8475cb4ca40fab03/hdclonise.part07.rar.html
http://letitbit.net/download/31515.3133cfaa19b625c5bbc0aad15b90/hdclonise.part08.rar.html
Mirror2 :

Código:
http://shareflare.net/download/94858.9a0857f2fd8c5e2f08784e4eeab7/hdclonise.part01.rar.html
http://shareflare.net/download/42403.4b1e9c9a4b0da383345134418ce9/hdclonise.part02.rar.html
http://shareflare.net/download/93660.950c0f897040af5badd5cc2b07a4/hdclonise.part03.rar.html
http://shareflare.net/download/70252.7f4831efb2399c80bba9eba8068d/hdclonise.part04.rar.html
http://shareflare.net/download/58161.5797a8eb49ae8b9b3e9e725efa80/hdclonise.part05.rar.html
http://shareflare.net/download/10990.190e95478b8d087a3d5071d9c445/hdclonise.part06.rar.html
http://shareflare.net/download/26962.2ddf726a15f3503aeaa23b0dc2f1/hdclonise.part07.rar.html
http://shareflare.net/download/14275.1569fe4d87e56b7b34185150d4a3/hdclonise.part08.rar.html
Mirror3 :

Código:
http://rapidgator.net/file/18029978/hdclonise.part01.rar.html
http://rapidgator.net/file/18029914/hdclonise.part02.rar.html
http://rapidgator.net/file/18029913/hdclonise.part03.rar.html
http://rapidgator.net/file/18029872/hdclonise.part04.rar.html
http://rapidgator.net/file/18029911/hdclonise.part05.rar.html
http://rapidgator.net/file/18029876/hdclonise.part06.rar.html
http://rapidgator.net/file/18029874/hdclonise.part07.rar.html
http://rapidgator.net/file/18029873/hdclonise.part08.rar.html
Mirror4 :

Código:
http://ryushare.com/444d94d2bdc3/hdclonise.part01.rar
http://ryushare.com/427beb889e04/hdclonise.part02.rar
http://ryushare.com/14198ea72beb/hdclonise.part03.rar
http://ryushare.com/444d94d2bdc2/hdclonise.part04.rar
http://ryushare.com/14198ea72bea/hdclonise.part05.rar
http://ryushare.com/15eb37f14c11/hdclonise.part06.rar
http://ryushare.com/444d94d2bdc1/hdclonise.part07.rar
http://ryushare.com/15eb37f14c10/hdclonise.part08.rar